We've discovered this great article pertaining to Tools You Need to Install a New Bathtub down the page on the net and concluded it made sense to write about it with you on this site.
Mounting a bath tub isn't precisely rocket science, however it does require solid plumbing, woodworking, and also often, tiling skills. Replacing an old tub with a new one is also a reasonably tough job. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the brand-new one. Ensure you have certified yourself for the job and also are comfortable attempting it. As opposed to employing a contractor to take over a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will assist you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and do not need to alter the arrangement of your previous water pipes.
Your devices and also material list should make up the following:
Preparing for the Setup
To start with, the supporting framework provided with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will come from the pipes. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub until the level checks out level.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water as well as inspect all joints and new pipework for leaks and also tighten them if needed. Fill the bath tub and also examine the overflow outlet and the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been used at least when as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bathroom as well as the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is suggested to fit the floor tiles utilizing waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub Yourself? Try leaving feedback down below. We'd be glad to see your feelings about this page. We hope that you come back again before long. Remember to take a moment to distribute this blog if you appreciated it. Thanks for taking the time to read it.
Schedule Appointment